Question about raw diseqc commands? Bug?

[jerryt]

Sould I be able to send the following raw diseqc command?

E0 31 6E E1 50

It is the "Go To XX" command from SS2diseqc1.9 which is working. But if I enter it into the raw diseqc comand box for that satellite, the motor does not responding.

Same with

E0 31 6B 10
Go to position 16 (Previously stored in motor), working with SS2Diseqc1.9

No response from motor



SS2 version 2.6

🌟 Recommended Tools & Services

• Formify.one - Free Online Form Creator (Better than Google Forms). - Create Professional Forms That Match Your Business, Form Builder That Actually Helps You Collect More Responses
• CrispShare - Screenshot Editor That Makes Your Work Look Professional (Without Design Skills). - Make Your Screenshots Stand Out in Crowded Social Feeds
• DVB Dream - Best TV Reception/Record software for your computer DVB add on. - Stop Missing Your Favorite Shows - Record TV Directly to Your PC. Turn Your Computer Into a Professional TV Recorder. Unlock Its Full Potential With Professional TV Software

[jerryt]

Ok, motor raw commands work fine with Genpix USB module. Either to a saved position or to a motor angle (Go toXX).

Not working with twinhan or skystar2, except skystar2 card works with SS2Diseqc1.9 plugin.

Relocation, Any suggestions for the Twinhan and Skystar?

Are diseqc switches working for people with these two cards and raw commands?

Motor raw commands;
Go to position 1 = E0 31 6B 01
Go to position 2 = E0 31 6B 02
Go to position 3 = E0 31 6B 03
Go to position 4 = E0 31 6B 04
Go to position 5 = E0 31 6B 05
Go to position 6 = E0 31 6B 06
Go to position 7 = E0 31 6B 07
Go to position 8 = E0 31 6B 08
Go to position 9 = E0 31 6B 09
Go to position 10 = E0 31 6B 0A
Go to position 11 = E0 31 6B 0B
Go to position 12 = E0 31 6B 0C
Go to position 13 = E0 31 6B 0D
Go to position 14 = E0 31 6B 0E
Go to position 15 = E0 31 6B 0F
Go to position 16 = E0 31 6B 10
Go to position 17 = E0 31 6B 11
Go to position 18 = E0 31 6B 12
Go to position 19 = E0 31 6B 13
Go to position 20 = E0 31 6B 14
Go to position 21 = E0 31 6B 15
Go to position 22 = E0 31 6B 16
Go to position 23 = E0 31 6B 17
Go to position 24 = E0 31 6B 18
Go to position 25 = E0 31 6B 19
Go to position 26 = E0 31 6B 1A
Go to position 27 = E0 31 6B 1B
Go to position 28 = E0 31 6B 1C
Go to position 29 = E0 31 6B 1D
Go to position 30 = E0 31 6B 1E

[rel]

raw diseqc is not supported by ss2 SDK 4.3.2 , it wont work.
I'm working on another ss2 device without using SDK.

twinhan.dev has raw diseqc support. here it's working with diseqc switches, I'm not sure why it wouldnt work with the motor.

[jerryt]

Skystar2 ver2.6
I am using techinsat drivers 4.4.0, but with Mili's plugin which requires a modified Skynet file 4.4.0 and Skydll.dll 4.3.2 was required in the system 32 folder.

Twinhan 1020a
I think I have the drivers included with Mytheatre, maybe 1.9

Should I try later drivers with the Twinhan.

Thanks Relocation!!!!



Windows XP

[jerryt]

OK, Upgraded my Twinhan drivers to 2.4.1.1

Still would not responding to a ten character raw diseqc command, "Go to XX" E0 31 6E E1 50 for 21.0 degrees east. The original Twinhan software is capable of sending USAL commands, so it must be possible for the driver.

But responds to an eight character raw diseqc command, "Go to position X" IE; E0 31 6B 0C. Dvbdream does not retune automatic-ly, so I have to reselect the channel.

Still no luck with the Skystar2 as raw commands, either eight or ten characters.

Genpix does the ten character raw diseqc just fine?


Any other suggestions Relocation?

[rel]

b2c2.dev uses offical b2c2 SDK 4.3.2. so it wont matter what driver version is used (4.4.0 or patched mibi drivers) raw diseqc is not supported on that.


just checked twinhan device, it seems that there is a limitation for max 4 bytes on the twinhan driver. I must find a way if it is possible to send more than 4 bytes.

[jerryt]

Thanks Relocation, you are the greatest!!!

Hopefully raw commands for USAL can work in the future. Thanks again for all your hard work, Dvbdream is a great product.

[jerryt]

Raw USAL commands work with Altdvb on both Twinhan and Skystar2 cards.

[scaistar]

raw diseqc is not supported by ss2 SDK 4.3.2 , it wont work.
I'm working on another ss2 device without using SDK.

RAW command are supported in 4.4 drivers
but it don't work with original Sky2PCAVSrc.ax but need a little patch.

I've tested it and work with SDKDemo.exe provided with SDK 1.11
If need more info write me
webmasterATscaistarDOTcom